1-877-4-SPRUCE | info@aircraftspruce.com
Aircraft Spruce & Specialty Co.
 
 
THE AVIATION SUPERSTORE FOR ALL YOUR AIRCRAFT & PILOT NEEDS | 877-4-SPRUCE
Home / Shopping Tools / AN Bolt Selector /AN Bolt Selector
Main Image

AN Bolt Selector

260 Reviews 9 Answered Questions
Quantity
Add to Wishlist

Overview

Hex head aircraft bolts are made of high-strength type 4037 or 8740 alloy steel (type 8740 is most commonly used). The bolts are center-less ground and threaded after heat treatment. Minimum tensile strength 125,000 PSI. Cadmium plated per specification QQ-P-416A, Type II, Class 3. Available with shank drilled for cotter pin or undrilled for stop nut application, & with or without drilled head for safety wire. Specify bolts to have undrilled shank by adding letter "A" after dash number. For bolts with drilled head add letter "H" after AN number. See illustrated examples. The length of AN aircraft bolts is measured from under the head to the end of the shank. The "grip" is the unthreaded portion of the shank. See table for conversion of length and/or grip to proper AN call-out.

Drawing

Reference Chart

  • Customers Also Viewed
  • Frequently Purchased With

Reviews

Submit a Review

its a bolt

Daniel A Verified Purchase

BOLT UNDRILLED AN4-30A
February 16, 2022

👍

Charles G Verified Purchase

BOLT UNDRILLED AN5-53A
February 10, 2022

As described, delivered quickly.

Patrick W Verified Purchase

BOLT UNDRILLED AN3-12A
February 8, 2022

I had to pound this one in deep but it was exactly what I needed.

Jim P Verified Purchase

BOLT UNDRILLED AN7-24A
February 3, 2022

James H Verified Purchase

BOLT UNDRILLED AN3-16A
February 1, 2022

James H Verified Purchase

BOLT UNDRILLED AN3-17A
February 1, 2022

James H Verified Purchase

BOLT UNDRILLED AN4-16A
February 1, 2022

James H Verified Purchase

BOLT UNDRILLED AN4-17A
February 1, 2022

James H Verified Purchase

BOLT DRILLED AN4-15
February 1, 2022

James H Verified Purchase

BOLT DRILLED AN3-6
February 1, 2022

Q&A

Please note, Aircraft Spruce's personnel are not certified aircraft mechanics and can only provide general support and ideas, which should not be relied upon or implemented in lieu of consulting an A&P or other qualified technician. Aircraft Spruce assumes no responsibility or liability for any issue or problem which may arise from any repair, modification or other work done from this knowledge base. Any product eligibility information provided here is based on general application guides and we recommend always referring to your specific aircraft parts manual, the parts manufacturer or consulting with a qualified mechanic.

Q: What is the diameter tolerance on a 3/8-24 AN bolt?

The max is .374", and min .371"

Q: What is the safety wire diameter recommended for the drilled version?

It depends on the application, but both .032 and .041 will fit through the hole.

Q: On a drilled shank, where is the hole located in reference to the end?

Per the Tech Data Sheet, the hole location is determined from the start of the threads, on the head side, to the center of the drilled hole. AN3 = 17/64", AN4 = 5/16", AN5 = 23/64", AN6 = 7/16", AN7 = 31/64", AN8 = 39/64".

Q: What is the difference between stainless and cadmium plated AN bolts?

Stainless bolts are corrosion resistant for applications where corrosion is a problem. CAD plated bolts are made of steel with CAD plating to help surface corrosion, but it can been worn or chipped off.

Q: Is the nominal length listed the entire bolt (head, grip and thread) or just the grip and thread?

The nominal length is the length from under the head to the end of the shank.

Q: Picture clearly shows a bolt with both head drilled and shank drilled, but bolt selector does not allow that choice?

We do offer all of the types shown, but unfortunately not in every size. For example, drilled head is not available in AN4-3 stainless, but is available in AN5-4 cadmium.

Q: For the drilled shank, what is diameter of the drilled hole on AN3?

It is drilled for 1/16" cotter pin so it will be slightly larger than 1/16".

Q: what is the diameter of an4 bolt?

1/4

Q: How do you measure the grip length?

The grip length is the unthreaded portion on the bolt.

View in Catalog

View Image View in Catalog